I picked up the final few bits and pieces that matter. I have a new favorite supplier, SAS in Shepshed. Click HERE for website. I had to file out the middle of the copper washer for the sump plug because I could not get the exact one. Given the alternative of waiting until late next week it was worth a bit of Dremell action. With the washer filed out to the exact size and sump plug refitted, I topped up the engine oil and then gave the sump plug an extra tweak. I was pleased to find it was not leaking.
Next up was to fill each suspension leg with the right amount of oil. Many years ago I picked up a 60mm syringe. It is just the job for measuring out the oil and for squirting the oil into the tiny filler hole on the top of the suspension leg. 230mm in each leg later, filler caps replaced and top covers tapped on, that job was done too. I had to cut cable ties that held the wires from each switch cluster in order to get access to the top of the suspension legs. It was a small job to refit the cable ties once the oil top up was completed.
I had bought an auxillary power socket some time ago. I decided today was the day to fit it. It went on well enough but it was a fiddle to route and connect the wires. I had to find a longer bolt for the battery terminal to accept the additional connectors. That job done I replaced the tool tray. The wires made the tray fit a little more snug.
The next job was to fit the clutch side hand grip. I wound a couple of turns of insulating tape round the handle bar and forced the grip on. It went on nice and tight but I can see it being a bugger to get off when I decide to connect the heater elements.
After that it was a nuts and bolts check. I moved the Landy so I could get the bike out of the garage. With the bike on the drive, choke lever engaged, I thumbed the starter button the engine turned over but it would not fire. I bit of coaxing and it did fire but just on the one cylinder. I bit of thought then a removed the float bowl from the none firing cylinder to find it was dry...no petrol. I was quite chuffed as I thought the engine sounded short of gas rather than short of spark. I flipped the floats a couple of time which made the petrol flow. I quickly replaced the float bowl since petrol was p*ssing out all over the drive. I thumbed the starter button again and this time she fired. The BM ran strongly if lumpy. The carbs definitely need balancing.
I pulled the clutch lever in and tried to engage a gear but nothing happened. I engaged a gear and dropped the clutch but the back wheel did not turn. I ran up the gear box and down again without success. I imagine all kinds of issues, incorrect clutch installation, iffy gearbox. I put those thoughts to the back of my mind and got a couple of spanners to adjust the free play on the clutch actuator rod. That did the trick. With the engine now idling off the choke I took a chance, dropped the bike off the stand. hooked first gear, revs and clutch out. As with all BM's off this vintage the torque lifted the bike and we were off. Just to the top of the street and back. A result. A couple of issue became apparent but the key thing is the bike runs, suspension and brakes work, and the bike feels quite balanced i.e. the wheels are in line. As it has been raining today and I spilled some petrol. The drive is covered with rainbow patches of petrol. It is still raining so the patches will wash off.
After my tentative trip to the top of the street I adjusted the back brake then left the bike to idle on the drive. The bike was up to temperature. The bike idled evenly over the twenty minutes it stood there. A checked over the bike afterwards to find, more accurately not to find any leaks. I gave the sump plug an eighth of a turn to stop the last little bit of an oil drip.
Asa final act I got the side panel down and fitted each one. The near side panel required my to remove the hand grip from the frame. . It was th work of a moment. With the tricky panel sorted I fitted the off-side panel too and hooked the rubber band between them. Job done th e bike was put back on the stand and a final job list created.
Monday, 30 May 2011
Sunday, 29 May 2011
Getting there
I sent for a new set of brake front pads from Motorworks. I was convinced I had the wrong pads as the front brake was binding on the disc and they were dragging the pads from there seating. The new pads were exactly the same as the ones on the bike. So that means the problem is else where. I re-read the manual. I figured it might be the adjustment of the caliper via the eccentric cam. Once the wheel was re-fitted I adjusted the calipers. That seemed to do the job. Unfortunately the bike is the wrong way round on the stand.
With the bike turned round I tackled the gear box and sump plug. I dropped the oil from the engine. The new oil pressure switch stopped part of the oil leak but the sump plug was still dripping. I took the sump plug out but that means you lose the oil too. The crush washer was not doing its job. I did not a washer to fit so I could not refilled the engine. Next up was the gear box oil. I took the drain plug out. There was no oil in the gearbox but the plug, which is magnetic, was covered in gunge. I cleaned the plug , as luck would have it, I had a crush washer in stock which I fitted when the plug was replaced. To top the oil up I had to remove the foot peg. That done I measured out the oil, 800cc of SAE 90's and squeezed it into the plug hole. When the oil level is right it dribbles out of the filler plug hole. It dribbled therefore it was full. I replaced the filler plug then the foot peg which just happens to have the gear selector attached.
I got the manual out to make a note of the oil volume for the engine. I need 2 3/4 litres of SAE 10/40's and the note the volume of the fork oil which is 280cc per leg of SAE 5's. Now I just have to go and buy the oil.
With the bike turned round I tackled the gear box and sump plug. I dropped the oil from the engine. The new oil pressure switch stopped part of the oil leak but the sump plug was still dripping. I took the sump plug out but that means you lose the oil too. The crush washer was not doing its job. I did not a washer to fit so I could not refilled the engine. Next up was the gear box oil. I took the drain plug out. There was no oil in the gearbox but the plug, which is magnetic, was covered in gunge. I cleaned the plug , as luck would have it, I had a crush washer in stock which I fitted when the plug was replaced. To top the oil up I had to remove the foot peg. That done I measured out the oil, 800cc of SAE 90's and squeezed it into the plug hole. When the oil level is right it dribbles out of the filler plug hole. It dribbled therefore it was full. I replaced the filler plug then the foot peg which just happens to have the gear selector attached.
I got the manual out to make a note of the oil volume for the engine. I need 2 3/4 litres of SAE 10/40's and the note the volume of the fork oil which is 280cc per leg of SAE 5's. Now I just have to go and buy the oil.
Sunday, 8 May 2011
A quickie
Having sorted out the items on the near side of the bike I had to turn it around again. It was really heavy again. Only when I got the bike back on the stand did I find out that the rear tyre was flat. I pumped it up to 35 psi. I will check it again in a few days to see if it held pressure.
I had a quick look at the bevel box. I cleaned and refitted the drain plug. I knew I had SAE90 oil in the cupboard. I checked the amount of oil in the carton. It was exactly the amount that is required by the bevel box. I filled the bevel box and fitted the filler plug.
Whilst had a minute I tightened up the bolts for the off side horn. I also cable tied the sleeved cables up to the clutch switch block.
I had a quick look at the bevel box. I cleaned and refitted the drain plug. I knew I had SAE90 oil in the cupboard. I checked the amount of oil in the carton. It was exactly the amount that is required by the bevel box. I filled the bevel box and fitted the filler plug.
Whilst had a minute I tightened up the bolts for the off side horn. I also cable tied the sleeved cables up to the clutch switch block.
Break Through Day
The first job of the day was to turn the bike round on the stand. The bike is heavier than I remember. It might be because the front brakes are binding.
Today was another break through day. I managed to fit the side stand spring. First time round I used a cable tie and a lever. The cable tie snapped. Next I used two cable ties and a lever. I just managed to to get the spring over the toggle on the side stand. Job done and it works properly. It only took three years to sort it out.
I had decided that the issue with the rear indicators and stop/tail lights was a wiring loom. After more than an hour of deliberation I discovered the fault. It was a issue dodgy earth. Fixing the fault was straight forward if fiddly. I also had to dismantle the rear light /indicator cluster, I cleaned it and carefully reassembled the cluster whist testing each step. Finally it was together and working. I then had to reassemble the loom and refit the relays, organise the wiring in the headlight shell and then refit the head light cluster. At each stage I tested the lights to ensure they worked. I an glad to say they did.
I fitted the near side horn and secured the wiring. It looks neat and the horns work....very loudly. With the horns fitted I then fitted the petrol tank. It was a bit of a fiddle. I hooked up the fuel lines. It is ready for fuel. Some of which I have in a Jerry can in Degsy. I cut a piece of insulating tape to length and stuck it to the rear sub frame to protect it from the seat hinge whilst fitting of the seat. I then fitted the seat. The seat needs a little work but money does not allow for such extravagances.
I discovered a new vendor from a magazine. They are SAS which have a branch in Shepshed. Click HERE from web site. I went along and found a deep 22mm socket which would allowed me to remove and replace the oil pressure switch. I did indeed replace the oil switch. The switch worked fine it allowed oil to pour out through the insulator even under static conditions. I hope the new one, now fitted, does a better job.
Unless I can get a set of instrument pods I will have to remove the Voltmeter and Clock. As it is they are dangling off the headlight shell.
Today was another break through day. I managed to fit the side stand spring. First time round I used a cable tie and a lever. The cable tie snapped. Next I used two cable ties and a lever. I just managed to to get the spring over the toggle on the side stand. Job done and it works properly. It only took three years to sort it out.
I had decided that the issue with the rear indicators and stop/tail lights was a wiring loom. After more than an hour of deliberation I discovered the fault. It was a issue dodgy earth. Fixing the fault was straight forward if fiddly. I also had to dismantle the rear light /indicator cluster, I cleaned it and carefully reassembled the cluster whist testing each step. Finally it was together and working. I then had to reassemble the loom and refit the relays, organise the wiring in the headlight shell and then refit the head light cluster. At each stage I tested the lights to ensure they worked. I an glad to say they did.
I fitted the near side horn and secured the wiring. It looks neat and the horns work....very loudly. With the horns fitted I then fitted the petrol tank. It was a bit of a fiddle. I hooked up the fuel lines. It is ready for fuel. Some of which I have in a Jerry can in Degsy. I cut a piece of insulating tape to length and stuck it to the rear sub frame to protect it from the seat hinge whilst fitting of the seat. I then fitted the seat. The seat needs a little work but money does not allow for such extravagances.
I discovered a new vendor from a magazine. They are SAS which have a branch in Shepshed. Click HERE from web site. I went along and found a deep 22mm socket which would allowed me to remove and replace the oil pressure switch. I did indeed replace the oil switch. The switch worked fine it allowed oil to pour out through the insulator even under static conditions. I hope the new one, now fitted, does a better job.
Unless I can get a set of instrument pods I will have to remove the Voltmeter and Clock. As it is they are dangling off the headlight shell.